Hard reset D-Link DIR-865L

D-Link DIR-865L
Factory reset (Hard reset)

Power ON the router. The reset button ‘hole’ is located on the side of the router (above the power switch) and is marked with red. Press in the hole with a thin object and hold for 6 seconds. Release. Wait for 1 min for the router to reboot.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-651

D-Link DIR-651

 

Factory reset (Hard reset)

Power ON the router. The reset button ‘hole’ is located on the back panel of the router – to the right of the right antenna. Press in it with a thin object (paperclip) and hold for about 10 seconds. Release. Wait for a minute until the router reboots.

Specifications Download PDF
Manual Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-857

D-Link DIR-857
Factory reset (Hard reset)

Power ON the device. The reset hole is located on the back panel of the router, it is marked with red. Press in it with a thin object and hold for 10 seconds. Release. Wait for 1 min for the router to reboot.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-605L

D-Link DIR-605L
Factory reset (Hard reset)

Power ON the router. The reset “hole” is located on the back of the router – to the right side of the right antenna. Use a thin object to press in and hold down for 10 seconds. Release. Wait a minute until the router reboots.

Specifications Download PDF
Manual Download PDF
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DGL-4500

D-Link DGL-4500
Factory reset (Hard reset)

Power ON the router. Locate the reset pin hole on the back (next to the USB port). Press it with a thin object (paperclip) and hold down for 5-10 seconds. Release and wait for 30-60 seconds for the reboot process to finish.

Specifications Download PDF
Manual Download PDF
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-825

D-Link DIR-825
Factory reset (Hard reset)

Power ON the router. The reset button is the small hole on the back panel – use a paperclip to hold it down for 10 seconds. Release. Wait 30 sec – 1 min for the reboot process to finish.

Specifications Download PDF
Manual Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-665

D-Link DIR-665
Factory reset (Hard reset)

Power On the router. Locate the reset pin hole on the back. Use a sharp object to press it and hold it down for 5 seconds. Release. … Important: If that does not work, try pressing the button and holding it down for 10 seconds, release.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DI-804HV

D-Link DI-804HV
Factory reset (Hard reset)

Turn OFF the router. Locate the reset pin hole on the back panel. Use a paper clip to press it and hold down for only about 5 seconds – don’t hold too long. Release. (You can also watch the lights on the front cover – it is time to release the button when M1 and M2 flash at the same time.)

Specifications Download PDF
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-300

D-Link DIR-300
Factory reset (Hard reset)

The reset button/hole is located on the back panel – to the right. Power on the router and use a paper clip or another sharp object to press the button down and hold for 10 seconds. Release. Wait about 30 seconds for the reboot process to finish.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-link DIR-130

D-Link DIR-130
Factory reset (Hard reset)

Power on the router. Find the reset “hole” on the back panel. Use a paper clip to press and hold the button down for 10 seconds. Release and wait about 30 seconds for the router to reboot. 

Specifications Download PDF
Manual Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1