Hard reset D-Link DGL-4300

D-Link DGL-4300
Factory reset (Hard reset)

Power ON the router. Locate the hard reset button hole on the back side. Put a paper clip in the hole and press down. Watch the LEDs on the front panel and release when all of them blink at the same time. Wait for the router to reboot (30sec – 1min).

Specifications Download PDF
Manual Download PDF
Firmware Link to support
Default username [none]
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-515

D-Link DIR-515
Factory reset (Hard reset)

Turn the router ON and locate the reset pin hole on the back panel. Use a paper clip to press in it and hold for 10 seconds. Release. Wait at least 30 seconds before trying to access the router.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-501

D-Link DIR-501
Factory reset (Hard reset)

Power ON your router. Locate the reset button hole on the rear panel. Use a paperclip to press the button and hold it down for 10 seconds. Release. Wait for a minute until the reset process has finished.

Specifications Download PDF
Manual Download PDF
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DAP-1560 access point

D-Link DAP-1560
Factory reset (Hard reset)

Power ON the access point. The reset button hole is on the back panel. Press in it with a thin object and hold for 10 seconds. Release. Wait for 30sec – 1min before accessing the device.

Specifications Download PDF
Default username admin
Default password [leave blank]
Default IP address 192.168.0.50

Hard reset D-Link DIR-657

D-Link DIR-657
Factory reset (Hard reset)

The reset button hole is on the back panel and is marked with red. Press it down with a thin object and hold for 10 seconds. Release. Wait a minute for the router to reboot.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-636L

D-Link DIR-636L
Factory reset (Hard reset)

Locate the reset button hole on the bottom of the device. Use a thin (sharp) object to press and hold the button down for 10 seconds. Wait for the router to reboot.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-826L

D-Link DIR-826L
Factory reset (Hard reset)

Power ON the router and locate the reset button (hole) on the bottom panel. Use a paperclip to hold the button down for 10 seconds. Release. Wait about 30 seconds for the reset process to finish.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DHP-1565

D-Link DHP-1565
Factory reset (Hard reset)

Power ON the router. Locate the reset button hole on the back panel. Use a paper clip to press it and hold down for 5 seconds. Release. Wait about 30-60 seconds for the reboot process to finish. PS. The power LED on the front panel lights up in orange during the factory reset process.

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-645

D-Link DIR-645
Factory reset (Hard reset)

The factory reset button hole is located on the bottom of the router – check the picture above. Power ON the router. Use a thin object (paperclip) to press and hold down the button for 10 seconds. Release. Wait about 30-60 seconds before accessing the router.

Specifications Download PDF
Manual Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1

Hard reset D-Link DIR-827

D-Link DIR-827
Factory reset (Hard reset)

Power ON the router. Locate the reset pin hole – it is on the back panel (next to the USB port) and is marked with red. Use a paper clip to press and hold down the button for 10 seconds. Release. Wait 30-60 seconds to access the router. 

Specifications Download PDF
Firmware Link to support
Default username admin
Default password [leave blank]
Default IP address 192.168.0.1