Hard reset TP-LINK Archer A2300

TP-LINK Archer A2300
Factory reset (Hard reset)

The Reset button (hole) is located on the side panel. Use a pin or paper clip to press and hold this button for more than 5 seconds. Release and wait for the router to reboot and reset to its factory default settings.

Firmware Link to support
Default username N/A
Default password You set it at http://tplinkwifi.net
Default IP address 192.168.0.1

Hard reset TP-LINK Archer AC3000

TP-LINK Archer AC3000
Factory reset (Hard reset)

The reset button is a hole located on the back panel of the router. Pressing this button (using a pin or a paper clip) for about 7 seconds resets the router to its factory default settings.

Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Hard reset TP-LINK AC5200 / Archer C5200

TP-LINK Archer C5200
Factory reset (Hard reset)

Turn on the device and find the Reset button which is a small hole on the back panel. Press this button for about 7 seconds to reset the router. Use a pin or paper clip if needed.

Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Hard reset TP-LINK TL-WR802N

TP-LINK TL-WR802N
Factory reset (Hard reset)

Locate the Reset button (hole) on the side of the device. With the device turned on, press and hold the button for a couple of seconds and wait for the router to reboot.

Default username admin
Default password admin
Default IP address 192.168.0.1

Hard reset TP-LINK TL-WR940N

TP-LINK TL-WR940N
Factory reset (Hard reset)

The reset button (hole) is located on the back of the router. Turn on the device and press and hold this button until the LED blinks to restore the router to its
factory default settings.

Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Hard reset TP-LINK TL-WR1043N

TP-LINK TL-WR1043N
Factory reset (Hard reset)

Turn on the device and locate the Reset button on the back panel. Press and hold this button until the Power LED blinks to reset the router to its factory default settings. Use a paper clip if needed.

Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Hard reset TP-LINK AC750 / TL-WR902AC

TP-LINK AC750 / TL-WR902AC
Factory reset (Hard reset)

Turn the device on and locate the Reset button (hole) on the side. Press and hold the Reset button for 5 seconds (use a paper clip if needed) to reset the router to the factory defaults.

Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Hard reset TP-LINK AC1200 / Archer C50

TP-LINK AC1200 / Archer C50
Factory reset (Hard reset)

Locate the WPS/RESET button on the back of the router. Press and hold the button for more than 5 seconds to reset
the router.

Firmware Link to support
Default username admin
Default password admin
Default IP address 192.168.0.1

Hard reset TP-LINK AC900 / Archer C900

TP-LINK AC900 / Archer C900
Factory reset (Hard reset)

Press and hold the Reset button on the back until the Power LED blinks to reset the router to its
factory default settings.

Firmware Link to support
Default username N/A
Default password You set it at http://tplinkwifi.net
Default IP address 192.168.0.1

Hard reset TP-LINK AC3150 / Archer C3150 V2

TP-LINK AC3150 / Archer C3150 V2
Factory reset (Hard reset)

Locate the reset button (hole) on the side of the router. With the device powered on, press and hold the Reset button for at least 5 seconds – all LEDs will light on Then release the button and wait the router to reboot to its factory default settings.

Firmware Link to support
Default username N/A
Default password You set it at http://tplinkwifi.net
Default IP address 192.168.0.1